<var id="fnfpo"><source id="fnfpo"></source></var>
<rp id="fnfpo"></rp>

<em id="fnfpo"><object id="fnfpo"><input id="fnfpo"></input></object></em>
<em id="fnfpo"><acronym id="fnfpo"></acronym></em>
  • <th id="fnfpo"><track id="fnfpo"></track></th>
  • <progress id="fnfpo"><track id="fnfpo"></track></progress>
  • <tbody id="fnfpo"><pre id="fnfpo"></pre></tbody>

  • Powerint LNK417EG 15W離線LED驅動電源方案(DER284)

    發布時間:2011-8-19 12:21    發布者:1770309616
    關鍵詞: LED驅動電源 , LNK417EG , Powerint
    Powerint公司的LinkSwitch-PH系列大大地簡化了實現功率因素大于0.9,TRIAC調光和高效率的LED驅動器的設計.器件集成了725V功率MOSFET,連續模式PWM控制器,用于自偏壓的高壓開關電流源,頻率抖動,逐個周期限流和滯后熱關斷電路,最適合用于離線LED驅動器.本文介紹了LinkSwitch-PH系列產品亮點, 功能方框圖, 14W和7W LED驅動器電路圖,以及采用LNK417EG無電解電容高效率(≥90%) PFC大于0.9的15W LED驅動器參考設計電路圖,主要指標和材料清單與PCB布局圖.

    LinkSwitch-PH dramatically simplifies implementation of LED drivers requiring Power Factors greater than 0.9, TRIAC dimming, and high efficiency. This highly integrated controller introduces a new control technique that provides very high power factor and accurate output current control, and eliminates passive circuitry required for power factor correction, optocoupler and secondary current control circuitry.

    Each device incorporates a 725V power MOSFET, a continuous-mode PWM controller, a high voltage switched current source for self biasing, frequency jittering, cycle-by-cycle current limit and hysteretic thermal shutdown circuitry into a monolithic IC.

    LinkSwitch-PH系列產品亮點:

    Dramatically Simplifies Off-line LED Drivers

    Single-stage power factor correction and accurate constant current (CC) output

    Flicker-free, phase-controlled TRIAC dimming

    Eliminates optocoupler and all secondary current control circuitry

    Eliminates all control loop compensation circuitry

    Simple primary-side PWM dimming interface

    Universal input voltage range

    Enables designs that are electrolytic-free

    Accurate and Consistent Performance

    Fast start-up time

    Compensates for transformer inductance tolerances

    Compensates for line input voltage variations

    Frequency jittering greatly reduces EMI filter size and costs

    Advanced Protection and Safety Features

    Auto-restart for short circuit protection

    Open circuit fault detection mode

    Automatic thermal shutdown or restart with hysteresis

    Meets high voltage creepage requirement between DRAIN and all other signal pins both on PCB and at package

    EcoSmart - Energy-Efficiency Technology

    Low standby power remote ON/OFF feature (< 50 mW at 230 VAC)

    No current sense resistors - maximizes efficiency

    High efficiency operation, >85% achievable

    Green Package

    Halogen free and RoHS compliant package

    LinkSwitch-PH應用:

    • Off-line LED driver

    圖1. LinkSwitch-PH系列功能方框圖

    圖2. LinkSwitch-PH系列絕緣TRIAC調光高功率因素通用輸入14W LED驅動器電路圖

    圖3. LinkSwitch-PH系列絕緣無調光高功率因素通用輸入7W LED驅動器電路圖 采用LNK417EG無電解電容高效率(≥90%) PFC大于0.9的15W LED驅動器參考設計

    This document describes an isolated, power factor corrected, very high efficiency LED driver designed to drive a 30 V LED string at a current of 500 mA (nominal). The input voltage range is 90 VAC to 265 VAC.

    The LED driver uses a LNK417EG device from the LinkSwitch-PH family of ICs. This integrated controller and 725 V MOSFET dramatically reduces the complexity and component count of the solution.

    The key design goals were to achieve the highest possible efficiency and eliminate electrolytic capacitors. Both are key factors for increasing the lifetime and reliability of LED drivers making this solution ideal for industrial and commercial applications.

    15W LED驅動器參考設計主要特性:

    No electrolytic capacitors

    Clean monotonic start-up – no output blinking

    Fast start-up (<100 ms) – no perceptible delay

    Highly energy efficient

    o ≥90% at 115 VAC and 230 VAC input Low cost, low component count and small printed circuit board footprint solution

    o No current sensing required

    o Frequency jitter for smaller, lower cost EMI filter components Integrated protection and reliability features

    o Output open-circuit / output short-circuit protected with auto-recovery

    o Line input overvoltage shutdown extends voltage withstand during line faults.

    o Auto-recovering thermal shutdown with large hysteresis protects both components and printed circuit board

    o No damage during brown-out or brown-in conditions

    Meets IEC 61000-4-5 ring wave, IEC 61000-3-2 Class C harmonics and EN55015 B conducted EMI


    圖4.15W LED驅動器參考設計外形圖: 3.115” L x 1.525” W.
    電源指標:


    圖5.15W LED驅動器參考設計電路圖


    圖6.變壓器電路圖
    變壓器主要指標:



    圖7. PCB布局圖(頂層)
    詳情請見:
    http://www.powerint.com/sites/default/files/product-docs/linkswitch-ph_family_datasheet.pdf

    http://www.powerint.com/sites/default/files/PDFFiles/der284.pdf
    本文地址:http://www.portaltwn.com/thread-73734-1-1.html     【打印本頁】

    本站部分文章為轉載或網友發布,目的在于傳遞和分享信息,并不代表本網贊同其觀點和對其真實性負責;文章版權歸原作者及原出處所有,如涉及作品內容、版權和其它問題,我們將根據著作權人的要求,第一時間更正或刪除。
    您需要登錄后才可以發表評論 登錄 | 立即注冊

    廠商推薦

    • Microchip視頻專區
    • 更佳設計的解決方案——Microchip模擬開發生態系統
    • 我們是Microchip
    • 利用模擬開發工具生態系統進行安全電路設計
    • Cortex-M4外設 —— TC&TCC結合事件系統&DMA優化任務培訓教程
    • 貿澤電子(Mouser)專區
    關于我們  -  服務條款  -  使用指南  -  站點地圖  -  友情鏈接  -  聯系我們
    電子工程網 © 版權所有   京ICP備16069177號 | 京公網安備11010502021702
    快速回復 返回頂部 返回列表
    精品一区二区三区自拍图片区_国产成人亚洲精品_亚洲Va欧美va国产综合888_久久亚洲国产精品五月天婷